edge

Rust edge agent for industrial IoT gateways. It polls Modbus (TCP / RTU) from PLCs and reads serial-ASCII weighing scales, then publishes each parameter to MQTT, one topic per value. Everything about a machine (IDs, connections, registers, poll interval) lives in a single JSON mapping file, so a new machine does not need a rebuild.

It runs on small ARM/x86 Linux boards (Raspberry Pi and similar) as a long-lived systemd service.

🇮🇩 Indonesia: README.id.md

Layout

Single package edge-client:

src/: the agent. Modbus polling and weigher reading, MQTT publishing, control gate, heartbeat and resource reporting.
src/shared/: mapping and Modbus domain types (JSON mapping schema, register semantics).
src/scale.rs: the edge-client scale subcommand, which prints raw scale serial output.

One edge-client instance runs one machine. That machine can have a primary PLC plus additional Modbus slaves and weighers on the same board. The agent stores nothing locally: everything is published to MQTT and consumed elsewhere.

Internally the agent spawns concurrent tasks via tokio::select!: the MQTT event-loop driver, the heartbeat/resource/telemetry/PLC-status/weigher publishers, and the control subscriber. Modbus RTU access is serialized through a per-port actor task so a single physical serial port is opened exactly once.

Quick start

# 1. Build
cargo build --release

# 2. Configure
cp deploy/edge-client/.env.example-edge-client .env       # broker credentials
cp example-mapping.json ./mapping.json                     # devices & registers
# edit .env (MQTT host/user/pass) and mapping.json (PLC IP, serial path, registers)

# 3. Run
MQTT_MAPPING_PATH=./mapping.json ./target/release/edge-client

Ready-made examples live at the repo root: example-mapping.json, example-mapping-plc-only.json, example-mapping-weigher-only.json, example-mapping-plc-slave-weigher.json.

Configuration (`.env`)

Machine configuration lives in the JSON mapping. The .env file only holds external connection credentials and a few runtime knobs.

Variable	Default	Description
`MQTT_HOST`	(required)	Broker host (or full host for ws/wss)
`MQTT_PORT`	(required)	Broker port (e.g. 1883, 8883, 443)
`MQTT_USERNAME`	(required)	Broker username
`MQTT_PASSWORD`	(required)	Broker password
`MQTT_CLIENT_ID`	(required)	Unique client id
`MQTT_PROTOCOL`	`mqtt`	`mqtt` (TCP), `mqtts` (TLS), `ws`, `wss`
`MQTT_WEBSOCKET_PATH`	`/mqtt`	WebSocket path (ws/wss only)
`MQTT_KEEPALIVE`	`60`	Keepalive seconds; the LWT fires after this timeout on a hard stop
`MQTT_PUBLISH_QOS`	`1`	Publish QoS: `0`, `1`, or `2`
`MQTT_MAPPING_PATH`	`./mapping.json`	Path to the JSON mapping
`CACHE_URL`	(empty)	Valkey/Redis URL for the control gate; empty = deny all control
`CONTROL_GATE_KEY`	`control`	Valkey hash key for the control gate
`RUST_LOG`	`info`	Tracing filter (e.g. `info`, `edge_client=debug`)

Mapping file

A single JSON document describes every device on the machine. The agent derives each MQTT topic as {base_topic}/{location}/{name}/{topic}.

{
  "base_topic": "acme/site",
  "poll_interval_ms": 1000,
  "devices": [
    /* ... */
  ],
  "bridge": [
    /* ... */
  ], // optional
}

The machine id is {location}/{name} of the first master device. If there is none, the first slave is used, then the first weigher.

Device types & connections

Each entry in devices[] has a device_type, a stable device_id (used for routing and bridge references), a location, a name, and a connection.

master: primary PLC. Sets the machine id and the main Modbus transport.
slave: additional Modbus device (RS-485 chiller, sensor panel, second PLC).
weigher: serial-ASCII weighing scale, no Modbus.

Connection types (connection.type):

// Modbus TCP
{ "type": "tcp", "host": "192.168.10.10", "port": 502, "unit_id": 1 }

// Modbus RTU over a serial port (USB-RS485, etc.)
{ "type": "rtu_serial", "unit_id": 8, "path": "/dev/ttyUSB0",
  "baud": 19200, "parity": "none", "stop_bits": 1, "data_bits": 8 }

// Serial ASCII (weigher scales)
{ "type": "serial_ascii", "path": "COM9",
  "baud": 9600, "parity": "none", "stop_bits": 1, "data_bits": 7 }

Multiple slaves on the same RS-485 bus (same path) share one actor task and are distinguished by unit_id, so the port is opened once. A tcp connection speaks Modbus TCP, so an Ethernet to RS-485 converter has to run as a Modbus TCP gateway. Raw RTU over TCP (the converter's transparent mode) exists as a transport in the code but cannot be selected from the mapping yet.

Parameters & categories

Each device declares parameters under three arrays:

monitoring[]: read and published as telemetry.
set[]: writable setpoints (float/integer), written on MQTT publish.
control[]: actuator on/off (register or coil), written on MQTT publish.

The array only decides the topic segment (set/ or control/). Whether a write goes through the control gate depends on modbus.kind, and the agent does not check that the two match. Keep write_multiple_registers in set[] and write_single_coil / write_single_register in control[].

A parameter looks like:

{
  "key": "temp_tank", // unique key (also the weigher regex capture name)
  "label": "Main Tank Temp", // human label
  "topic": "temp/tank", // topic suffix
  "type": "float", // float | integer | boolean | string
  "unit": "C", // optional
  "modbus": {
    /* binding, see below; omit for weigher params */
  },
}

A parameter without a modbus binding is not polled by Modbus (used for weigher capture-group values).

Readback

Add "readback": true to a set[] or control[] entry to have the agent read its write address back every poll cycle and publish the value to {base_topic}/{location}/{name}/state/{topic} (e.g. .../state/control/lamp). A consumer can use this as the PLC state, for example to skip a command whose value is already set. It also reflects changes made from an HMI/panel, as long as the HMI writes the same address.

write_single_coil: read with FC1, published as "true" / "false".
write_single_register: read with FC3. on_value becomes "true", off_value becomes "false", any other value is not published. Two entries that share one register (e.g. lift up = 4, lift down = 8, off = 0) each only report their own value, so while the register is 4 the "down" state is not published.
write_multiple_registers: read with FC3 using the same byte_order as the write, published as a number.

Reads are grouped by address into requests under the Modbus limits (125 registers / 2000 coils), separate from the telemetry bulk read. A device whose readback fails is skipped for 30 s. Enable readback only if the PLC keeps the written value at that address.

Modbus bindings

modbus.kind maps directly to a Modbus function code:

`kind`	FC	Use
`read_coils`	FC1	Bulk read boolean bits from address 0 (`monitoring`)
`read_discrete_inputs`	FC2	Targeted single-bit read (`monitoring`)
`read_holding_registers`	FC3	Bulk read float/integer from address 0 (`monitoring`)
`read_input_registers`	FC4	Targeted read at a sparse address (`monitoring`)
`write_single_coil`	FC5	Write 1 boolean bit (`control`)
`write_single_register`	FC6	Write 1 register with an on/off value (`control`)
`write_multiple_registers`	FC16	Write 2 registers (float32/int32 setpoint) (`set`)

Examples:

// FC3 monitoring float, big/little byte order
{ "kind": "read_holding_registers", "address": 10, "byte_order": "big_little" }

// FC4 with a scale multiplier (e.g. raw 250 → 25.0)
{ "kind": "read_input_registers", "address": 1000, "scale": 0.1 }

// FC5 control coil
{ "kind": "write_single_coil", "address": 4 }

// FC6 control register: value 1 on true, 3 on false
{ "kind": "write_single_register", "address": 6, "on_value": 1, "off_value": 3 }

// FC16 setpoint (2 registers)
{ "kind": "write_multiple_registers", "address": 26, "byte_order": "big_big" }

read_holding_registers and read_input_registers decode a 32-bit value from 2 registers. With scale, read_input_registers instead reads 1 register and multiplies.
off_value defaults to 0 when omitted.

Byte order

32-bit values span two 16-bit registers; vendors differ on packing order:

`byte_order`	Byte	Word	Typical vendor
`big_big`	BE	BE	Schneider, ABB ("network order")
`little_big`	LE	BE	Siemens S7
`big_little`	BE	LE	Schneider Quantum, some Modicon
`little_little`	LE	LE	some Mitsubishi / generic

Defaults to big_big when omitted. If a value decodes as garbage, try swapping byte and/or word order.

Weigher parser & commands

A weigher device reads ASCII lines from serial and parses them with a regex using named capture groups. Each group name must match a monitoring key.

"parser": {
  "regex": "[A-Za-z-]*(?P<weight>[-+]?[0-9]+\\.[0-9]+)(?P<unit>[A-Za-z]*)",
  "byte_map": [ { "from": 176, "to": 48 } /* 0xB0→'0' … 0xB9→'9' */ ],
  "raw_topic": "raw",          // optional: also publish all groups as one JSON object
  "stable": { "group": "st", "equals": "ST" }, // optional: publish only settled readings
  "read_timeout_ms": 5000       // optional: reopen the port if silent this long
}

byte_map remaps raw bytes before ASCII decode, for brands that encode digits as non-standard bytes (e.g. GSC uses 0xB0–0xB9 for '0'–'9'). Leave it empty for standard-ASCII brands (e.g. Fujitsu).
raw_topic, if set, publishes {"weight": 12.50, "unit": "kg"} to {base}/{location}/{name}/{raw_topic} alongside the per-key topics.
stable gates publishing on the scale's stable/motion flag: add a capture group for the status token (e.g. (?P<st>ST|US)) and set group/equals. Only lines whose token equals equals are published, so in-motion readings are dropped. Omit to publish every parsed line.
read_timeout_ms is an idle watchdog: if the port stays open but sends nothing for this long, the connection is reopened (catches a silent-but-open port). Omit for poll/on-demand scales that are idle between reads; set it to a few times the output interval for continuous scales.

Optional commands[] let an operator drive the scale over serial from MQTT. Publishing to {base}/{location}/{name}/cmd/{key} writes the command's serial_cmd bytes to the port (escapes: \r \n \t \\ \xNN):

"commands": [
  { "key": "tare",  "serial_cmd": "T\\r\\n" },
  { "key": "zero",  "serial_cmd": "Z\\r\\n" },
  { "key": "print", "serial_cmd": "P\\r\\n" }
]

Scale notes

Settings used for the scales in the weighing room. All of them are weigher devices with a serial_ascii connection and no Modbus. The connection blocks differ per brand, so do not copy one to another scale without checking.

GSC

Serial: 9600 baud, 7 data bits, no parity, 1 stop bit.
Digits are sent as bytes 0xB0 to 0xB9 instead of ASCII '0' to '9', so byte_map maps bytes 176 to 185 onto 48 to 57.
The regex has an optional st group for the ST/US status token. It is published in the raw JSON, but no stable rule is set, so in-motion lines are published too.
Commands end with CR LF: T tares, Z zeroes, P prints.

"connection": { "type": "serial_ascii", "path": "COM3",
  "baud": 9600, "parity": "none", "stop_bits": 1, "data_bits": 7 },
"parser": {
  "regex": "(?:(?P<st>ST|US)\\D*?)?(?P<weight>[-+]?[0-9]+\\.[0-9]+)(?P<unit>[A-Za-z]*)",
  "byte_map": [
    { "from": 176, "to": 48 }, { "from": 177, "to": 49 },
    { "from": 178, "to": 50 }, { "from": 179, "to": 51 },
    { "from": 180, "to": 52 }, { "from": 181, "to": 53 },
    { "from": 182, "to": 54 }, { "from": 183, "to": 55 },
    { "from": 184, "to": 56 }, { "from": 185, "to": 57 }
  ],
  "raw_topic": "raw"
},
"commands": [
  { "key": "tare",  "serial_cmd": "T\\r\\n" },
  { "key": "zero",  "serial_cmd": "Z\\r\\n" },
  { "key": "print", "serial_cmd": "P\\r\\n" }
]

Fujitsu (analytical balance)

Serial: 9600 baud, 8 data bits, no parity, 1 stop bit.
Output is standard ASCII, so byte_map stays empty.
Each reading is a multi-line record with one field per line: TTYPE, ID, DATE, TIME, TEMP, BAT, MODE, REF, STATUS, STEP, TARE, ZERO, WT. The weight line looks like WT:0.00g, or WT:-0.12g after a tare. The unit is grams.
The parser works per line, so the regex is anchored on WT:. Without it, lines such as TEMP:25.9C, BAT:7.1V or REF:2000.00g are captured as weight too. [-+]? is needed, otherwise negative readings do not match and are dropped without a warning.
The stable rule cannot be used: STATUS:STEADY is on a different line from WT:, so the status group never matches the weight line and every line would be rejected. All readings are published.
Commands end with CR LF: T tares, Z zeroes, P prints.

"connection": { "type": "serial_ascii", "path": "/dev/ttyUSB0",
  "baud": 9600, "parity": "none", "stop_bits": 1, "data_bits": 8 },
"parser": {
  "regex": "WT:\\s*(?P<weight>[-+]?[0-9.]+)\\s*(?P<unit>\\D+)",
  "byte_map": [],
  "raw_topic": "raw"
},
"commands": [
  { "key": "tare",  "serial_cmd": "T\\r\\n" },
  { "key": "zero",  "serial_cmd": "Z\\r\\n" },
  { "key": "print", "serial_cmd": "P\\r\\n" }
]

Radwag WLC/C2 (60 kg)

Serial: 9600 baud, 8 data bits, no parity, 1 stop bit (Radwag RS232 default).
Output is standard ASCII, so byte_map stays empty.
The regex was checked against the scale. It is not anchored and takes the first number (integer or decimal) followed by a unit anywhere in the line.
There is no stable rule, so in-motion lines (marked ?, ^ or v by the scale) are published together with stable ones.
Commands end with CR LF: T tares, Z zeroes, and print sends S (Radwag's "send stable result" command).

"connection": { "type": "serial_ascii", "path": "COM4",
  "baud": 9600, "parity": "none", "stop_bits": 1, "data_bits": 8 },
"parser": {
  "regex": "(?P<weight>[-+]?\\d+(?:\\.\\d+)?)\\s*(?P<unit>[A-Za-z]+)",
  "byte_map": [],
  "raw_topic": "raw"
},
"commands": [
  { "key": "tare",  "serial_cmd": "T\\r\\n" },
  { "key": "zero",  "serial_cmd": "Z\\r\\n" },
  { "key": "print", "serial_cmd": "S\\r\\n" }
]

Gewinn XK3118T1

Read from the indicator's DB9 RS232 port, which is separate from the load cell port.
Serial: 2400 baud, 8 data bits, no parity, 1 stop bit. The baud rate was confirmed with a Web Serial test tool.
The indicator runs in communication mode Co 3: a continuous stream of net weight and unit, about 7.8 frames per second, resolution 0.02 kg, each frame ending with CR LF. A frame looks like =0000.14(kg), a negative one like =-000.06(kg). The regex skips the ( between the number and the unit.
Co 3 frames have no stable flag, so the stable rule cannot be used. Stable detection (window plus tolerance) is not implemented.
Commands: the XK3118T1 manual lists tare as STX E ETX and zero as STX D ETX, for mode Co 5 (command-response). Tested in Co 3, the indicator does not reply and the stream does not change. Co 5 has not been tested.
The manual has no serial print command. Print is tied to the physical accumulate key and only outputs in mode Co 6 when TOTAL is pressed. The print command is kept with an empty serial_cmd until this is confirmed on the device.

"connection": { "type": "serial_ascii", "path": "COM4",
  "baud": 2400, "parity": "none", "stop_bits": 1, "data_bits": 8 },
"parser": {
  "regex": "(?P<weight>[-+]?\\d+\\.\\d+)\\D*?(?P<unit>[A-Za-z]+)",
  "byte_map": [],
  "raw_topic": "raw"
},
"commands": [
  { "key": "tare",  "serial_cmd": "\\x02E\\x03" }, // no effect in Co 3
  { "key": "zero",  "serial_cmd": "\\x02D\\x03" }, // no effect in Co 3
  { "key": "print", "serial_cmd": "" }             // not validated
]

Bridge rules

Not implemented yet. bridge[] rules are parsed and their format is fixed, but no task runs them, so nothing is copied. The plan is to copy a value read from one device into a setpoint on another every poll cycle, without going through the control gate.

"bridge": [
  {
    "read_from": { "device": "slave1", "key": "temp_out_chiller" },
    "write_to":  { "device": "plc1",   "key": "set_temp_tank" },
    "transform": "passthrough"
  }
]

MQTT topic layout

All topics are prefixed {base_topic}/{location}/{name} (the machine id):

Topic	Direction	Payload
`.../{param.topic}`	publish	Raw scalar string, one per monitoring param
`.../heartbeat`	publish	`{"status":"connected"}` every 1s (retained)
`.../resources`	publish	`{"memory_pct","cpu_pct","ip"}` every 1s
`.../plc/status`	publish	`{"status":"connected"\|"disconnected"}`
`.../control/{key}`	subscribe	`"1"`/`"0"`/`"true"`/`"false"`, actuator write
`.../set/{key}`	subscribe	Numeric string, setpoint write
`.../cmd/{key}`	subscribe	Any payload, sends the weigher `serial_cmd`
`.../state/{topic}`	publish	Readback of `set`/`control` entries, see Readback

The broker Last-Will-Testament publishes {"status":"disconnected"} (retained) to the primary machine's heartbeat topic if the agent dies or the network drops. After a broker reconnect the agent re-subscribes automatically (rumqttc runs a clean session).

The agent does not check who published to control/, set/ or cmd/, and it has no dedup, ack or audit log. If you need those, put a service in front of the agent that receives commands on its own topics and forwards them, and use broker ACLs so that only this service can publish to the agent's control/#, set/# and cmd/# topics.

Control gate

Writes with modbus.kind write_single_coil or write_single_register (FC5/FC6, the control[] actuators) are authorized by a Valkey/Redis hash before each write. write_multiple_registers writes (FC16, the set[] setpoints) and weigher cmd/{key} commands are not checked.

A write is granted only if both the global flag and the per-machine flag are "1":

redis-cli HSET control global 1
redis-cli HSET control acme/site/area2/machine_c 1

The per-machine field name is {base_topic}/{machine_id}, the same identifier as the MQTT topic prefix.

The gate fails closed. Control is denied when:

CACHE_URL is empty.
Valkey is unreachable at startup. The agent does not retry this connection, so control stays denied until the agent restarts.
HGETALL fails at runtime (that command is denied).
CONTROL_GATE_KEY is set but empty (CONTROL_GATE_KEY=). The empty value is used as the hash key instead of the default, and a hash with an empty name normally has no flags. Remove the line to use the default control.

Diagnosing a scale (`scale`)

Before writing a weigher parser, use the built-in subcommand to inspect the raw serial output (correct baud rate, encoding, line terminator):

edge-client scale                          # pick a port interactively
edge-client scale --port COM3 --baud 4800  # a specific port/baud
edge-client scale --port COM3 --scan       # try common baud rates (3s each)
edge-client scale --port COM3 --send "T\r\n"  # send tare before reading
edge-client scale --list                   # list serial ports and exit

Each line prints HEX | printable-ASCII. Readable text means the baud is right; dots (.) where digits should be usually mean a non-ASCII encoding you can fix with a byte_map in the mapping.

Cross-compilation

build.sh builds edge-client for a target inside a container and drops the binary into bin/:

bash build.sh armv7-musl        # Raspberry Pi OS 32-bit, static (recommended)
bash build.sh armv7-glibc       # Raspberry Pi OS 32-bit, dynamic glibc
bash build.sh aarch64           # Raspberry Pi OS 64-bit / ARM64
bash build.sh x86_64            # Linux x86_64, dynamic glibc
bash build.sh x86_64-musl       # Linux x86_64, static
bash build.sh win-x86_64-gnu    # Windows x86_64 (mingw-w64)
bash build.sh win-x86_64-msvc   # Windows x86_64 (MSVC ABI via cargo-xwin)

Run bash build.sh with no arguments to list all targets.

License

Licensed under the MIT License.

Name		Name	Last commit message	Last commit date
.github/workflows		.github/workflows
deploy		deploy
src		src
.gitignore		.gitignore
AGENTS.md		AGENTS.md
Cargo.lock		Cargo.lock
Cargo.toml		Cargo.toml
LICENSE		LICENSE
Makefile		Makefile
README.id.md		README.id.md
README.md		README.md
build.sh		build.sh
example-mapping-plc-only.json		example-mapping-plc-only.json
example-mapping-plc-slave-weigher.json		example-mapping-plc-slave-weigher.json
example-mapping-weigher-only.json		example-mapping-weigher-only.json
example-mapping.json		example-mapping.json
rust_client.service		rust_client.service

Navigation Menu

Repository navigation

About

Repository files navigation

edge

Contents

Layout

Quick start

Configuration (`.env`)

Mapping file

Device types & connections

Parameters & categories

Readback

Modbus bindings

Byte order

Weigher parser & commands

Scale notes

GSC

Fujitsu (analytical balance)

Radwag WLC/C2 (60 kg)

Gewinn XK3118T1

Bridge rules

MQTT topic layout

Control gate

Diagnosing a scale (`scale`)

Cross-compilation

License

About

Releases

Packages

Contributors

Languages

Latest commit

History

Folders and files

Repository files navigation

edge

Contents

Layout

Quick start

Configuration (.env)

Mapping file

Device types & connections

Parameters & categories

Readback

Modbus bindings

Byte order

Weigher parser & commands

Scale notes

GSC

Fujitsu (analytical balance)

Radwag WLC/C2 (60 kg)

Gewinn XK3118T1

Bridge rules

MQTT topic layout

Control gate

Diagnosing a scale (scale)

Cross-compilation

License

About

Topics

Resources

Stars

Watchers

Forks

Releases

Packages

Contributors

Languages

Configuration (`.env`)

Diagnosing a scale (`scale`)